Projecte

General

Perfil

Actions

Wiki » Historial » Revisió 15

« Anterior | Revisió 15/68 (diferencies) | Següent »
Axel Neumann, 27-08-2012 08:34


BMX6

Bmx6 is a routing protocol for Linux based operating systems.
The following intro provides kind of tutorial to get started.

Installation

Requirements

The following tools are needed to obtain, compile, and install bmx6
  • git (debian package: git-core)
  • gcc
  • make

Downloading

Latest development sources are available from bmx6 git repository

git clone git://qmp.cat/bmx6.git
cd bmx6

Compile and Install

To only compile the main bmx6 daemon (no bmx6 plugins)

make
sudo make install

Usage (hello mesh)

In its most simple configuration, the only required parameter are the interfaces names that should be used for meshing.
The following example starts bmx6 on interface wlan0:

root@mlc1001:~# bmx6 dev=eth1

However, to let this simple command work as expected also check the following basic requirements:

  • bmx6 must be executed in root context (with super user permissions). If you are not already root, prepend all commands with sudo (eg: sudo bmx6 dev=eth1 ).
  • NO IP address needs to be configured. By default bmx6 assumes IPv6 and autoconfigures an ULA based IPv6 address for each interface based on the MAC address of the device. Just, the interfaces must be UP. The linux ip command can do this for you (eg: ip link set wlan0 up ). Also, if you are using a wireless interface, the wireless interface settings must be set correctly so that link-layer connectivity is given with bmx6 daemons running on other nodes (computers). The good old iwconfig command may help to achieve that. For example iwconfig wlan0 mode ad-hoc ap 02:ca:ff:ee:ba:be channel 11 essid my-mesh-network is a typical configuration for a wireless mesh setup.
  • Bmx6 (by default) works in daemon mode, thus sends itself to background and gives back a prompt. To let it run in foreground specify a debug level with the startup command like: bmx6 debug=0 dev=eth1 . Of course you may need to kill a previously started bmx6 daemon beforehand ( killall bmx6 )

If everything went fine bmx6 is running now, searching for neighboring bmx6 daemons via the configured link, and coordinates with them to learn about existence-of and routes-to all other bmx6 nodes in the network.

To access status information of the bmx6 daemon which has just been started, a second bmx6 process can be launched in client mode (with the --connect or -c parameter) to connect to the main bmx6 daemon and retrieve the desired information.

In the following, a few example will be discussed:

root@mlc1001:~# bmx6 -c status
version        compatibility codeVersion globalId                     primaryIp                       myLocalId uptime     cpu nodes 
BMX6-0.1-alpha 16            9           mlc1001.E0F9E33CD42EF2980443 fd66:66:66:0:a2cd:efff:fe10:101 24100101  0:00:56:37 0.3 3

So apart from version, compatibility number, and code, the status reveals the daemon's global and local ID, its primary (self-configured) IPv6 address, the time since when it is running (56 minutes), its current cpu consumption (0.3%) and the total number of learned nodes in the network (including itself).

Typical types of accessible information are: status, interfaces, links, originators, descriptions, tunnels
These required types can be combined. Also the above given example shows kind of shortcut. The long argument would be
bmx6 connect show=status . So a more informative case using the long form would be:

root@mlc1001:~# bmx6 connect show=status show=interfaces show=links show=originators show=tunnels
status:
version        compatibility codeVersion globalId                     primaryIp                       myLocalId uptime     cpu nodes 
BMX6-0.1-alpha 16            9           mlc1001.7A7422752001EC4AC4C8 fd66:66:66:0:a2cd:efff:fe10:101 06100101  0:00:06:52 0.1 3    
interfaces:
devName state type     rateMin rateMax llocalIp                    globalIp                           multicastIp primary 
eth1    UP    ethernet 1000M   1000M   fe80::a2cd:efff:fe10:101/64 fd66:66:66:0:a2cd:efff:fe10:101/64 ff02::2     1       
links:
globalId                     llocalIp                 viaDev rxRate txRate bestTxLink routes wantsOgms nbLocalId 
mlc1000.0AE58311046412F248CD fe80::a2cd:efff:fe10:1   eth1   100    100    1          1      1         9B100001  
mlc1002.91DCF042934B5913BB00 fe80::a2cd:efff:fe10:201 eth1   100    100    1          1      1         BB100201  
originators:
globalId                     blocked primaryIp                       routes viaIp                    viaDev metric lastDesc lastRef 
mlc1000.0AE58311046412F248CD 0       fd66:66:66:0:a2cd:efff:fe10:1   1      fe80::a2cd:efff:fe10:1   eth1   999M   407      1      
mlc1001.7A7422752001EC4AC4C8 0       fd66:66:66:0:a2cd:efff:fe10:101 0      ::                       ---    128G   410      0      
mlc1002.91DCF042934B5913BB00 0       fd66:66:66:0:a2cd:efff:fe10:201 1      fe80::a2cd:efff:fe10:201 eth1   999M   410      1

Only if relevant information for a requested type is available it will be shown.
In this example no tunnels are configured nor offered by other nodes and therefore no tunnel information is shown.

The loop argument can be prepended to the connect argument to continuously show the requested information.
Many of the long arguments are usable via a short notation, like l for loop, c for connect, s for show, d for debug.
And there is another shortcut summarizing my current favorite information types via debug level 8
The following commands do the same as above: bmx6 -lc status interfaces links originators tunnels or just bmx6 -lcd8 .

Reviewing the provided info:
  • interfaces: Followed by one line per configured interface
    • dev: Interface name
    • state and type: Whether the interface is UP or DOWN and its assumed link-layer type.
    • rateMin and rateMax: Min- and maximum transmit rates assumed for this interface.
    • llocalIp: IPv6 link-local address (used as source address for all outgoing protocol data).
    • globalIp: Autoconfigured address used for sending network traffic via this interface and which is propagated to other nodes.
    • multicastIp: Multicast IP (used as destination address for all bmx6 protocol traffic send via this interface).
    • primary: Indicates whether the global ip of this interface is used as primary ip for this daemon.
  • links: Followed by one line per detected neighboring bmx6 node.
    • globalId: GlobalId of that neighbor (see: Wiki ).
    • llocalIp: Link-local IP of the neighbor's interface building the other side of the link.
    • viaDev: Interface of this node for the link.
    • rxRate: Measured receive rate in percent for the link.
    • txRate: Measured transmit rate in percent for the link.
    • bestTxLink: Indicates whether this link is the best link to a neighboring nodes.
    • routes: Indicates for how much routes to other nodes this link is used.
    • wantsOgms: Indicates whether the neighboring node has requested (this node) to propagate originator messsages (OGMs) via this link.
    • nbLocalId: Neighbors local ID.
  • originators: Followed by one line per aware originator in the network (including itself).
    • globalId: Global Id of that node (see: Wiki ).
    • blocked: Indicates whether this node is currently blocked (see: Wiki ).
    • primaryIp: The primary IP of that node.
    • routes: Number of potential routes towards this node.
    • viaIp: Next hops link-local IP of the best route towards this node.
    • viaDev: Outgoing interface of the best route towards this node.
    • metric: The end to end path metric to this node
    • lastDesc: Seconds since the last description update was received (see: Widi )
    • lastRef: Seconds since this node was referenced by any neighboring node (like last sign of life)

Concepts

Global ID

Unicast Host Network Announcements (UHNA)

Tunnel Announcements

Descriptions

Blocked

Nodes may be blocked by other nodes.

The decision for blocking another node is done locally based on the detection of duplicate claimed unique resources.
This happens if two nodes are declaring themselves as the owner of a unique resource. Then one of those two nodes (usually the latter) is blocked to avoid the propagation of conflicting state. Duplicate address usage is the most common reason for such events which happens if two nodes are using (and announcing) the same primary IPs. Another typical reason for such events is the rebooting of a node. Once the bmx6 daemon restarts it appears as a new node to the network but announcing the same address as the previous process. Since the resources allocated by the previous resources are still in the database of other nodes in the mesh they will block the new process until this information expires (by default after 100 seconds).

Bmx6 Plugins

Config Plugin

Requirements

uci libs are needed for the bmx6-config plugin.
To install it do:

wget http://downloads.openwrt.org/sources/uci-0.7.5.tar.gz
tar xzvf uci-0.7.5.tar.gz
cd uci-0.7.5
make
sudo make install

Depending on your system there happens to be an error during compilation.
Then edit cli.c and change line 465 to: char *argv[MAX_ARGS+2];

Compile and Install

To compile the bmx6 daemon and bmx6 plugins

make build_all
sudo make install_all

Usage

Json Plugin

Requirements

  • json-c for bmx6_json plugin (debian package: libjson0 libjson0-dev)

json-c developer libs are needed!
For further reading check: http://json.org/ or https://github.com/jehiah/json-c

Note for debian sid:
The debian package libjson0-dev 0.10-1 seems to miss the file /usr/include/json/json_object_iterator.h
Manually copying it from the below mentioned json-c_0.10.orig.tar.gz archive helps.

To install manually (only if NOT installed via debian or other package management system):

wget http://ftp.de.debian.org/debian/pool/main/j/json-c/json-c_0.10.orig.tar.gz
tar xzvf json-c_0.10.orig.tar.gz
cd json-c..
./configure ; make ; make install; ldconfig

Compile and Install

To compile the bmx6 daemon and bmx6 plugins

make build_all
sudo make install_all

Usage

SMS Plugin

Quagga Plugin

Misc

Tunnel

Actualitzat per Axel Neumann fa més de 11 anys · 15 revisions